Industry Application Guide

Pipe Flanges & Fittings for Water & Wastewater Infrastructure

Flanges & fittings for water treatment, distribution, and wastewater: carbon steel & stainless, AWWA and ASME B16.5 compliant. Get a written quote.

Industry Sector Overview

Heavy-duty carbon steel and stainless steel flanges designed for municipal water treatment plants, cross-country water supply mains, sewage pumping stations, and desalination plants.

Flanges in Treatment Plants, Pumping Stations and Mains

Water and wastewater treatment plants use flanges on pump discharge headers, filter galleries, chemical dosing and air scour lines. Pumping stations need large weld neck or slip-on flanges on suction and delivery mains, plus blind flanges for future connections. Transmission mains use flanges at valves, meters, air valves and scour points.

Many of these connections bolt to ductile iron valves and pumps with flat faces, so the steel flange should be flat face with a full-face gasket. A raised-face steel flange bolted to a flat-face iron flange can crack the iron.

Desalination Plants

Seawater reverse osmosis plants combine low-pressure intake and pretreatment lines with high-pressure feed and brine lines running at several tens of bar. High-pressure seawater lines typically use super duplex F53 or F55, intake and brine discharge may use duplex, and product water lines use 316L. Each zone has a different line class.

Matching Drilling Standards

Water projects mix ASME B16.5, EN 1092-1 PN10 and PN16, BS 10 Table D and E on older UK-pattern networks, and AWWA C207 on large steel mains. These are not interchangeable. Give the standard and class of the mating flange or valve, or send its drawing, so drilling is confirmed in the quotation.

Critical Operating Challenges & Design Constraints

Large-diameter piping connections subject to soil settlement and ground movement
Corrosion from untreated sewage, industrial effluent, and soil moisture
High volume procurement requiring strict cost control and reliable delivery schedules

Recommended Material Grade Selection Matrix

Material GradeSpecific Application & Fluid Service
ASTM A105 / A36 Carbon SteelPotable water distribution lines
ASTM A182 F304 / F316Corrosive wastewater & chemical dosing
Duplex 2205High-salinity desalination intake lines

Recommended Flange Types

Large Diameter Slip-On & Blind Flanges
ASME B16.47 Series A & B Flanges
Flat Face AWWA Mating Flanges

Quality Assurance, Testing & Specification Compliance

Material Traceability & Metallurgical Testing

Every flange manufactured for Water Infrastructure Industry Flanges is forged from 100% prime tested steel billets with complete melt-heat traceability. Remax Forge performs Spectro chemical analysis, tensile testing, yield strength verification, elongation measurement, and Brinell or Vickers hardness checks according to ASTM A105, A182, A350, and ASME Section II standards.

For critical fluid handling and high-pressure duties, we execute Positive Material Identification (PMI) testing using calibrated XRF analyzers, Charpy V-notch impact testing at design minimum temperatures (down to -46°C for A350 LF2 or cryogenic conditions for austenitic alloys), and grain size examination compliant with ASTM E112.

Hydrostatic, NDT & Third-Party Inspection

Non-destructive examination (NDE) procedures including 100% Ultrasonic Testing (UT) for internal defect detection, Liquid Penetrant Inspection (LPI), and Magnetic Particle Inspection (MPI) are conducted per ASME Section V specifications.

Every dispatch is accompanied by an EN 10204 Type 3.1 Mill Test Certificate (MTC) detailing complete chemical, mechanical, and heat-treatment batch records. Independent third-party inspection (TPI) by global authorities including Lloyd's Register, Bureau Veritas, DNV-GL, TÜV, and SGS is routinely facilitated upon project requisition.

Recommended Material & Product Guides

Industry FAQs

Q: Do you supply AWWA-standard flanges or ASME B16.5 flanges for water projects?

A: Remax Forge produces standard ASME B16.5 and B16.47 flanges up to 60 inches, which fully meet or exceed AWWA Class D/E pressure ratings. Custom AWWA flange dimensions are manufactured upon request.

Q: Which material is used for wastewater flanges?

A: Carbon steel with the coating your project specifies for general lines, and 304L or 316L stainless where hydrogen sulphide or aggressive effluent is present.

Q: Can you supply EN 1092-1 PN16 flanges for water projects?

A: Yes. EN 1092-1 flanges are made to order. Give the DN, PN, type number and material.

Q: Which flange suits SWRO high-pressure lines?

A: Super duplex F53 or F55 are commonly specified. The project line class sets the grade and class.

Sector Specific Inquiry

Request Quote for Water Infrastructure Industry Flanges

Get a written technical offer with the certification you specify.