Weld neck, slip-on and blind flanges for hydro, lift-irrigation and water lines around Loktak Lake, made at our ISO 9001:2015 works in Mumbai and sent by road with EN 10204 3.1 certificates. The lead time is stated on your written quote.
High-volume water diversion, penstocks & cooling loops: Large-Diameter Flanges, Concentric Reducers.
Lead time for Bishnupur is stated on your written quote.
Heat numbers marked on every piece; third-party inspection accepted.
Carbon, alloy, stainless and duplex grades supplied with an EN 10204 3.1 MTC.

Bishnupur district holds most of Loktak Lake, and the hydro and lift-irrigation works built around it are where flange orders come from. Remax Forge supplies weld neck flanges for power stations, slip-on flanges for water works and blind (BL) flanges from our Mumbai works, to ASME B16.5 or EN 1092-1, with an EN 10204 3.1 MTC. Buyers in the valley can also see our pages for Imphal and Churachandpur.
At Remax Forge & Fittings, every order is built to the governing standard. For high-pressure steam, oil and gas, and chemical utilities, all piping hardware is manufactured under a certified ISO 9001:2015 quality management system in our Mumbai facility. Before dispatching any order to Bishnupur, every item undergoes rigorous destructive and non-destructive quality testing. This includes Positive Material Identification (PMI), hydrostatic pressure testing, ultrasonic flaw detection, and dimensional audits to ASME B16.5, B16.47, and B16.11 standards. Every dispatch is accompanied by an EN 10204 3.1 Mill Test Certificate (MTC), dimensional reports, and compliance docs.
Loktak Lake lies in Bishnupur district, south of Imphal, and is a Ramsar site. The Ithai barrage on the Manipur River was built as part of the Loktak multipurpose project to give regulated storage for 105 MW of power and for lift irrigation. NHPC lists the Loktak power station at 105 MW in three 35 MW units, and reporting in 2025 said its modernisation plan was waiting on approvals. Moirang, a sub-division of the district, sits on the western edge of the lake.
That mix decides the flange list. Station overhaul and cooling-water work usually means weld neck flanges and blinds in A105, matched to the pipe schedule. Lift-irrigation pump sets and the distribution mains from them use slip-on or plate flanges in Class 150 or PN10/PN16, often hot-dip galvanised. Where a pump discharge needs isolating for maintenance, a spectacle blind in the same class saves cutting the line.
For a Bishnupur order, quote the line size and the flange drilling the pump or valve already has. Many older pumps are drilled to PN10 or PN16 and will not mate with a Class 150 flange of the same nominal size, so tell us which one is on site and we will match it on the quote.
| Service | Flanges & fittings usually specified |
|---|---|
| Hydro station cooling water and overhaul | Weld neck RF, ASME B16.5 Class 150/300, A105 |
| Lift-irrigation pump discharge | Slip-on or plate, Class 150 or EN 1092-1 PN10/PN16, galvanised option |
| Pump and valve isolation | Spectacle blind or blind flange in the line class |
| Treated water mains | SS 304 slip-on or A105 weld neck, PN16 |
What we quote most often for Loktak Lake and the Ithai barrage, Moirang, Imphal. Sizes, classes and grades below are those listed on our flange product pages; anything else is quoted against your specification.
| Types we quote | weld neck flanges for power stations, slip-on flanges for water works, blind (BL) flanges, plus blinds and spectacle blinds in the same class |
|---|---|
| Dimension standards | ASME B16.5 (NPS ½"–24"), ASME B16.47 Series A/B (NPS 26"–60"), EN 1092-1 (PN6–PN400) |
| Rating range | Class 150, 300, 400, 600, 900, 1500, 2500; PN6 to PN400 |
| Grades for Bishnupur service | A105 carbon steel for station and pump work; SS 304/316 for treated water; hot-dip galvanising on request |
| Face options | RF, FF, RTJ, tongue & groove, male & female |
| Certificates | EN 10204 3.1 MTC with heat number on each piece; 3.2 on request |
| Dispatch | By road from Mumbai to Bishnupur; lead time on the written quote |

Weld neck, slip-on, blind and threaded flanges to ASME B16.5 / B16.47 in A105, A350 LF2 (low-temp), Class 150–2500, for hydro power piping in Bishnupur.

ASME B16.9 elbows, tees, concentric and eccentric reducers and caps, seamless or welded and matched to your pipe schedule, for power & boiler lines in Bishnupur.

ASME B16.11 socket-weld and threaded fittings in 3000# and 6000# (9000# on request) for small-bore drain, vent, instrument and hydraulic lines at food & agro units in Bishnupur.
Flanges and forged fittings are made under an ISO 9001:2015 quality system at our Mumbai works. Alloy and stainless lots get 100% PMI, and hydrostatic, ultrasonic, radiography and magnetic particle testing are available on request. Every dispatch ships with an EN 10204 3.1 MTC.
CNC machining and in-house forging cover standard and drawing-based parts: forged fittings in 2000#, 3000#, 6000# and 9000#, and flange faces in RF, FF, RTJ, tongue & groove and male-female.
We export to 45+ countries, including the UAE, USA and Saudi Arabia. Common sizes and grades are held in stock, so ex-stock orders are dispatched within 24–48 hours.
Our team helps you pick the pressure class, material grade and face type for your service conditions. You are welcome to audit the Mumbai works in person or by video before ordering.
Precision-engineered components for mission-critical environments.

High-volume water diversion, penstocks & cooling loops
Large-Diameter Flanges, Concentric Reducers

Superheated steam lines, IBR boiler circuits & exhaust pipes
Alloy Steel P91/F22 Flanges, IBR Fittings

Sanitary grade pipelines and food manufacturing lines
SS 304/316 Flanges, Buttweld Elbows
Route: Road freight from Mumbai to Bishnupur. The lead time and delivery schedule depend on the items and testing ordered and are stated on the written quote. Packing: crates or pallets with rust-preventive coating. Docs: invoice, packing list, EN 10204 3.1 MTC, test reports as ordered.
Wooden crates or pallets, with rust-preventive coating and wrapping to protect machined faces in transit and site storage.
Invoice, packing list, EN 10204 3.1 MTC, PMI reports, hydro test reports, and IBR documentation (if applicable) are dispatched with every order.


























































































We can quote weld neck, blind and spectacle blind flanges to ASME B16.5 in A105 or stainless, with an EN 10204 3.1 MTC, for overhaul and cooling-water lines at the Loktak station. We are not an NHPC-approved vendor, so send the contractor's specification and we will quote against it.
Match what is already on the pump or valve. Older sets are often drilled to PN10 or PN16 (EN 1092-1), newer packaged pumps to ASME Class 150. The bolt circles differ, so check the drilling or send a photo of the flange, and we will quote the matching standard.
Yes. Slip-on and plate flanges can be hot-dip galvanised after machining for raw-water and irrigation lines. State the coating on the RFQ so it appears on the quote and on the inspection plan.
Yes. List each site's delivery point on the RFQ. We quote item by item, mark each line with its destination and state the lead time and freight for each on the written quote.
Orders go by road from our Mumbai works. The lead time depends on the types, sizes and tests ordered, so it is stated item by item on the written quote for Bishnupur rather than as a fixed number of days.
No. Manufacturing and testing are at our ISO 9001:2015 works in Mumbai, and Bishnupur orders are sent from there by road. We have no office or warehouse in Bishnupur.
EN 10204 3.1 mill test certificates, with dimensional reports and hydro, UT or PMI reports as ordered. A 3.2 certificate can be arranged when the specification calls for it.