Slip-on, weld neck and lap joint flanges for Imphal's water treatment plants and the Takyelpat industrial estate, made at our ISO 9001:2015 works in Mumbai and sent by road with EN 10204 3.1 certificates. The lead time is stated on your written quote.
Municipal water distribution, water treatment & supply mains: Mild Steel Flanges, Concentric Reducers, Weld Bends.
Lead time for Imphal is stated on your written quote.
Heat numbers marked on every piece; third-party inspection accepted.
Carbon, alloy, stainless and duplex grades supplied with an EN 10204 3.1 MTC.

Imphal's newest water source is the Thoubal multipurpose project, and its treatment and distribution works are a steady source of flange orders. Remax Forge supplies slip-on flanges for water works, lap joint (LJ) flanges and weld neck (WN) flanges from our Mumbai works with an EN 10204 3.1 MTC. See also Bishnupur and Thoubal.
At Remax Forge & Fittings, every order is built to the governing standard. For high-pressure steam, oil and gas, and chemical utilities, all piping hardware is manufactured under a certified ISO 9001:2015 quality management system in our Mumbai facility. Before dispatching any order to Imphal, every item undergoes rigorous destructive and non-destructive quality testing. This includes Positive Material Identification (PMI), hydrostatic pressure testing, ultrasonic flaw detection, and dimensional audits to ASME B16.5, B16.47, and B16.11 standards. Every dispatch is accompanied by an EN 10204 3.1 Mill Test Certificate (MTC), dimensional reports, and compliance docs.
The Thoubal multipurpose project, also known as the Mapithel dam, was officially inaugurated in December 2020. A CAG report gives its design aim as adding 45.46 MLD of drinking water for Imphal city and the areas around it, alongside irrigation and hydropower. In 2023 the Chingkheiching treatment plant was drawing water from the dam.
Takyelpat Industrial Estate in Imphal West is the main estate in the district. It houses the MSME Development Institute and MANIDCO, and CIPET lists several HDPE pipe makers there. HDPE lines are joined to valves and steel pipe with a stub end and a loose backing flange, which is a lap joint flange or a plate flange drilled to the matching PN or class.
For a treatment plant, the flange list is mostly slip-on and weld neck flanges in PN10/PN16 for filters, clear-water tanks and pump headers, plus blinds for future tie-ins. State the drilling standard the existing valves use, since Imphal water works use both EN 1092-1 and ASME drilling.
| Service | Flanges & fittings usually specified |
|---|---|
| Treatment plant pump headers | Slip-on or weld neck, EN 1092-1 PN10/PN16, A105 |
| HDPE stub-end joints | Lap joint or plate backing flanges, PN10/PN16 drilling, galvanised |
| Clear-water mains and tie-ins | Slip-on and blind flanges, Class 150 or PN16 |
| Estate workshops | Threaded and socket weld flanges, Class 150/300 |
What we quote most often for Takyelpat Industrial Estate, Chingkheiching water treatment plant, Thoubal multipurpose project (Mapithel dam). Sizes, classes and grades below are those listed on our flange product pages; anything else is quoted against your specification.
| Types we quote | slip-on flanges for water works, lap joint (LJ) flanges, weld neck (WN) flanges, plus blinds and spectacle blinds in the same class |
|---|---|
| Dimension standards | ASME B16.5 (NPS ½"–24"), ASME B16.47 Series A/B (NPS 26"–60"), EN 1092-1 (PN6–PN400) |
| Rating range | Class 150, 300, 400, 600, 900, 1500, 2500; PN6 to PN400 |
| Grades for Imphal service | A105 and galvanised carbon steel for water works; SS 304 where the treated water spec asks for stainless |
| Face options | RF, FF, RTJ, tongue & groove, male & female |
| Certificates | EN 10204 3.1 MTC with heat number on each piece; 3.2 on request |
| Dispatch | By road from Mumbai to Imphal; lead time on the written quote |

Weld neck, slip-on, blind and threaded flanges to ASME B16.5 / B16.47 in A105, SS 304, galvanized options, Class 150–2500, for water & utility piping in Imphal.

ASME B16.9 elbows, tees, concentric and eccentric reducers and caps, seamless or welded and matched to your pipe schedule, for food & agro lines in Imphal.

ASME B16.11 socket-weld and threaded fittings in 3000# and 6000# (9000# on request) for small-bore drain, vent, instrument and hydraulic lines at food & agro units in Imphal.
Flanges and forged fittings are made under an ISO 9001:2015 quality system at our Mumbai works. Alloy and stainless lots get 100% PMI, and hydrostatic, ultrasonic, radiography and magnetic particle testing are available on request. Every dispatch ships with an EN 10204 3.1 MTC.
CNC machining and in-house forging cover standard and drawing-based parts: forged fittings in 2000#, 3000#, 6000# and 9000#, and flange faces in RF, FF, RTJ, tongue & groove and male-female.
We export to 45+ countries, including the UAE, USA and Saudi Arabia. Common sizes and grades are held in stock, so ex-stock orders are dispatched within 24–48 hours.
Our team helps you pick the pressure class, material grade and face type for your service conditions. You are welcome to audit the Mumbai works in person or by video before ordering.
Precision-engineered components for mission-critical environments.

Municipal water distribution, water treatment & supply mains
Mild Steel Flanges, Concentric Reducers, Weld Bends

Sanitary grade pipelines and food manufacturing lines
SS 304/316 Flanges, Buttweld Elbows
Route: Road freight from Mumbai to Imphal. The lead time and delivery schedule depend on the items and testing ordered and are stated on the written quote. Packing: crates or pallets with rust-preventive coating. Docs: invoice, packing list, EN 10204 3.1 MTC, test reports as ordered.
Wooden crates or pallets, with rust-preventive coating and wrapping to protect machined faces in transit and site storage.
Invoice, packing list, EN 10204 3.1 MTC, PMI reports, hydro test reports, and IBR documentation (if applicable) are dispatched with every order.


























































































Yes. For HDPE stub-end joints we supply lap joint flanges or plate backing flanges drilled to EN 1092-1 PN10/PN16 or ASME Class 150, galvanised or painted. Give the HDPE pipe OD and the drilling you need to mate with.
Yes. Pump headers, filter connections and clear-water mains use slip-on, weld neck and blind flanges in PN10/PN16 or Class 150. Send the BOQ and we will quote item by item with an EN 10204 3.1 MTC.
Both EN 1092-1 (PN) and ASME B16.5 drilling are found, depending on the valve and pump supplier. Check the existing equipment or the tender drawings and state the standard on the RFQ so the bolt holes line up.
Yes. Threaded, slip-on and socket weld flanges can be quoted in small lots. We don't publish a minimum order, so state the quantity you need and the quote will show the price for it.
Orders go by road from our Mumbai works. The lead time depends on the types, sizes and tests ordered, so it is stated item by item on the written quote for Imphal rather than as a fixed number of days.
No. Manufacturing and testing are at our ISO 9001:2015 works in Mumbai, and Imphal orders are sent from there by road. We have no office or warehouse in Imphal.
EN 10204 3.1 mill test certificates, with dimensional reports and hydro, UT or PMI reports as ordered. A 3.2 certificate can be arranged when the specification calls for it.