Standard Specification

EN 1092-1 European Flange Standard — PN Ratings & Type 01-37

EN 1092-1 European flange specification guide: PN6 to PN400, Type 01, 02, 05, 11, 12, 13, 21, facing types A-H, material groups, dimensions. Get a written quote.

Standard Overview & Scope

EN 1092-1 is the harmonized European standard for circular steel flanges. Replacing obsolete national standards like DIN 2501 across the EU, it standardizes PN pressure designations and facing types A through H.

Official Standard Scope

EN 1092-1 specifies requirements for circular steel flanges in PN designations from PN 2.5 to PN 400 and nominal sizes from DN 10 to DN 4000.

Covered Size RangeDN 10 to DN 4000
Pressure Ratings / ClassesPN 2.5, PN 6, PN 10, PN 16, PN 25, PN 40, PN 63, PN 100, PN 160, PN 250, PN 320, PN 400

EN 1092-1 Flange Types and Their DIN Equivalents

Most RFQs still arrive with a DIN number. The EN 1092-1 type that replaces it keeps the same mating dimensions, so the flange bolts to existing pipework: Type 05 blind replaces DIN 2527, Type 01 plate slip-on replaces DIN 2573 / 2576, Type 11 weld neck replaces DIN 2631 to 2635 (for example DIN 2633 PN 16 becomes EN 1092-1 Type 11 PN 16), and Type 13 hubbed threaded replaces DIN 2566.

Type 02 loose plate flanges fit over a separate weld-on collar, the European counterpart of a lap joint flange and stub end. Type 12 is a hubbed slip-on flange for welding.

Materials for EN 1092-1 Flanges

Carbon steel Type 11 weld neck flanges are commonly made in P250GH, the EN designation of the older DIN grade C22.8. Stainless flanges are forged from EN 10222-5 or equivalent ASTM A182 material: 1.4301 (304), 1.4404 (316L) and 1.4462 duplex are the grades buyers ask for most.

A PN 10 or PN 16 Type 11 weld neck in 1.4404 is the direct replacement for a stainless DIN 2632 / 2633 flange. Allowable pressure depends on the material and the design temperature, so state both on the RFQ and check the pressure-temperature table of EN 1092-1 for the grade you specify.

PN 10 vs PN 16 Drilling

PN 10 and PN 16 flanges share the same drilling up to DN 150. From DN 200 the bolt-hole count differs, so check the PN of the mating flange before you order a replacement. A PN 16 flange bolted to a PN 10 flange is rated only to PN 10.

Dimensional Tolerances, Gasket Facings & Standard Marking

Facing Finishes & Gasket Compatibility

Under EN 1092-1 Flange Standard, flange sealing face finishes are critical to leak-free joint integrity. Raised Face (RF) and Flat Face (FF) flanges are machined with a serrated concentric or serrated spiral finish having an average surface roughness between 125 µin and 250 µin (3.2 µm to 6.3 µm Ra), creating an ideal gripping surface for spiral wound or non-asbestos sheet gaskets.

For severe cyclic service or high-pressure hydrocarbons, Ring Type Joint (RTJ) grooves are precision CNC-machined to ASME B16.20 standards. Groove surfaces are finished to a mirror-smooth 63 µin (1.6 µm Ra) max roughness to ensure tight metallic sealing against octagonal or oval ring gaskets.

Standard Marking & Traceability Requirements

Compliance with EN 1092-1 Flange Standard requires permanent identification legibly stamped on the outer rim of every flange: manufacturer trademark ("REMAX"), governing standard, nominal pipe size (NPS or DN), pressure rating class (e.g. 150#, 300#, 600#), ASTM/ASME material specification and grade (e.g. A105, F316L), schedule/wall thickness, and unique heat batch number.

All markings correlate 1:1 with the accompanying EN 10204 Type 3.1 Mill Test Certificate (MTC), providing verified traceability back to the initial steel melting ladle and forging ingot.

Related Standard & Material Guides

EN 1092-1 Flange Supply Range and RFQ Checklist

EN 1092-1 flanges are quoted against your specification, marked with the type number, PN and material, with an EN 10204 3.1 certificate. Sizes, classes and grades outside this list are quoted against your specification.

TypesType 01 plate, Type 02 loose plate, Type 05 blind, Type 11 weld neck, Type 12 hubbed slip-on, Type 13 hubbed threaded
PN ratingsPN 6, PN 10, PN 16, PN 25, PN 40 and higher PN on request
FacingsType A flat face, Type B1/B2 raised face, other facing types on request
Grades commonly orderedP250GH (C22.8) carbon steel, 1.4301 (304), 1.4404 (316L), 1.4462 duplex
DocumentsEN 10204 3.1 (3.2 on request)

RFQ checklist: what to send for an accurate quote

  • Flange type (weld neck, slip on, blind, socket weld, threaded, lap joint, spectacle blind)
  • Nominal size (NPS or DN) and quantity per size
  • Pressure class (ASME 150–2500) or PN rating (EN 1092-1)
  • Facing: raised face (RF), flat face (FF) or ring type joint (RTJ)
  • For weld neck and socket weld: pipe schedule or bore
  • Material grade (e.g. ASTM A105, A182 F316L, A350 LF2)
  • Dimensional standard (ASME B16.5, B16.47 Series A/B, EN 1092-1, ...)
  • Required certificates and tests (EN 10204 3.1 / 3.2, NACE MR0175, third-party inspection)
  • Delivery point and required date, plus your preferred Incoterm

Standard Specification FAQs

Q: What is the difference between EN 1092-1 Facing B1 and B2?

A: B1 is standard raised face roughness (Ra 3.2 to 12.5 µm) for PN 2.5 to PN 40. B2 is fine turned surface finish (Ra 0.8 to 3.2 µm) required for higher pressure PN ratings (PN 63 and above).

Q: Which EN 1092-1 type replaces DIN 2633?

A: DIN 2633 is a PN 16 weld neck flange. Its EN 1092-1 replacement is a Type 11 weld neck flange in PN 16, which has the same mating dimensions.

Q: What material is used for carbon steel EN 1092-1 flanges?

A: P250GH is the usual carbon steel grade for Type 11 weld neck flanges; it replaces the DIN grade C22.8. Stainless flanges are commonly 1.4301 (304) or 1.4404 (316L).

Flange RFQ Form

Request Quote for EN 1092-1 Flange Standard

Get dimensional data and a written quotation.