Weld neck, slip-on and blind flanges for Aizawl's pumped water mains and the Zuangtui industrial estate, made at our ISO 9001:2015 works in Mumbai and sent by road with EN 10204 3.1 certificates. The lead time is stated on your written quote.
Municipal water distribution, water treatment & supply mains: Mild Steel Flanges, Concentric Reducers, Weld Bends.
Lead time for Aizawl is stated on your written quote.
Heat numbers marked on every piece; third-party inspection accepted.
Carbon, alloy, stainless and duplex grades supplied with an EN 10204 3.1 MTC.

Aizawl takes its water from the Tlawng river, pumped a long way uphill, so pumping mains are the city's biggest flange load. Remax Forge supplies weld neck (WN) flanges, slip-on flanges for water works and blind (BL) flanges from Mumbai to ASME B16.5 or EN 1092-1 with an EN 10204 3.1 MTC. For other Mizoram towns see Kolasib and Champhai.
At Remax Forge & Fittings, every order is built to the governing standard. For high-pressure steam, oil and gas, and chemical utilities, all piping hardware is manufactured under a certified ISO 9001:2015 quality management system in our Mumbai facility. Before dispatching any order to Aizawl, every item undergoes rigorous destructive and non-destructive quality testing. This includes Positive Material Identification (PMI), hydrostatic pressure testing, ultrasonic flaw detection, and dimensional audits to ASME B16.5, B16.47, and B16.11 standards. Every dispatch is accompanied by an EN 10204 3.1 Mill Test Certificate (MTC), dimensional reports, and compliance docs.
The Greater Aizawl Water Supply Scheme pumps water from the Tlawng river up to the city. A CAG audit of Phase-II describes vertical turbine pump sets lifting from the Tlawng, and in May 2024 the Phase-I pumping station on the riverbank flooded during Cyclone Remal and supply had to be suspended. Repairs and replacement after events like that need pump discharge flanges, rising-main flanges and blinds at short notice.
Zuangtui is the main industrial estate in Aizawl district. An MSME district profile lists 42.12 hectares developed there, with 233 plots. Units of that size order smaller lots: threaded and slip-on flanges in Class 150, socket weld flanges for compressed air and small-bore lines, and a few blinds for test points.
High-head rising mains are where the rating matters. A main that lifts water several hundred metres runs at a pressure where PN10 is not enough, so check the design pressure at the pump end and order PN16, PN25 or Class 300 there, stepping down along the line. Put the working pressure on the RFQ and we will confirm the class on the quote.
| Service | Flanges & fittings usually specified |
|---|---|
| Rising mains from the Tlawng | Weld neck RF, Class 150/300 or EN 1092-1 PN16/PN25, A105 |
| Vertical turbine pump discharge | Weld neck or slip-on to the pump drilling, with blind for isolation |
| Estate workshops and utilities | Threaded and socket weld flanges, Class 150, A105 |
| Treated water distribution | Slip-on, PN10/PN16, galvanised or SS 304 |
What we quote most often for Zuangtui industrial estate, Tlawng river pumping stations, Sairang. Sizes, classes and grades below are those listed on our flange product pages; anything else is quoted against your specification.
| Types we quote | weld neck (WN) flanges, slip-on flanges for water works, blind (BL) flanges, plus blinds and spectacle blinds in the same class |
|---|---|
| Dimension standards | ASME B16.5 (NPS ½"–24"), ASME B16.47 Series A/B (NPS 26"–60"), EN 1092-1 (PN6–PN400) |
| Rating range | Class 150, 300, 400, 600, 900, 1500, 2500; PN6 to PN400 |
| Grades for Aizawl service | A105 for pumping mains; SS 304/316 for treated water; galvanised slip-on flanges on request |
| Face options | RF, FF, RTJ, tongue & groove, male & female |
| Certificates | EN 10204 3.1 MTC with heat number on each piece; 3.2 on request |
| Dispatch | By road from Mumbai to Aizawl; lead time on the written quote |

Weld neck, slip-on, blind and threaded flanges to ASME B16.5 / B16.47 in A105, SS 304, galvanized options, Class 150–2500, for water & utility piping in Aizawl.

ASME B16.9 elbows, tees, concentric and eccentric reducers and caps, seamless or welded and matched to your pipe schedule, for food & agro lines in Aizawl.

ASME B16.11 socket-weld and threaded fittings in 3000# and 6000# (9000# on request) for small-bore drain, vent, instrument and hydraulic lines at food & agro units in Aizawl.
Flanges and forged fittings are made under an ISO 9001:2015 quality system at our Mumbai works. Alloy and stainless lots get 100% PMI, and hydrostatic, ultrasonic, radiography and magnetic particle testing are available on request. Every dispatch ships with an EN 10204 3.1 MTC.
CNC machining and in-house forging cover standard and drawing-based parts: forged fittings in 2000#, 3000#, 6000# and 9000#, and flange faces in RF, FF, RTJ, tongue & groove and male-female.
We export to 45+ countries, including the UAE, USA and Saudi Arabia. Common sizes and grades are held in stock, so ex-stock orders are dispatched within 24–48 hours.
Our team helps you pick the pressure class, material grade and face type for your service conditions. You are welcome to audit the Mumbai works in person or by video before ordering.
Precision-engineered components for mission-critical environments.

Municipal water distribution, water treatment & supply mains
Mild Steel Flanges, Concentric Reducers, Weld Bends

Sanitary grade pipelines and food manufacturing lines
SS 304/316 Flanges, Buttweld Elbows
Route: Road freight from Mumbai to Aizawl. The lead time and delivery schedule depend on the items and testing ordered and are stated on the written quote. Packing: crates or pallets with rust-preventive coating. Docs: invoice, packing list, EN 10204 3.1 MTC, test reports as ordered.
Wooden crates or pallets, with rust-preventive coating and wrapping to protect machined faces in transit and site storage.
Invoice, packing list, EN 10204 3.1 MTC, PMI reports, hydro test reports, and IBR documentation (if applicable) are dispatched with every order.


























































































It depends on the head at the pump end. A high-lift main from the Tlawng runs well above PN10, so the pump-end flanges are often PN25 or Class 300, stepping down along the line. Send the design pressure and we will confirm the class for each section on the quote.
Yes. Send the size, class or PN, facing and material of each flange, or photos with the drilling measured, and we will quote replacements to match the existing pumps and valves. The lead time is written on the quote.
Yes. Threaded, slip-on and socket weld flanges can be quoted in small quantities. We don't publish a minimum order, so put the quantity you need on the RFQ and the quote will show the price for it.
Our standard dispatch is by road from Mumbai. If you prefer a rail booking to Sairang, say so on the RFQ and we will confirm on the quote whether it can be arranged.
Orders go by road from our Mumbai works. The lead time depends on the types, sizes and tests ordered, so it is stated item by item on the written quote for Aizawl rather than as a fixed number of days.
No. Manufacturing and testing are at our ISO 9001:2015 works in Mumbai, and Aizawl orders are sent from there by road. We have no office or warehouse in Aizawl.
EN 10204 3.1 mill test certificates, with dimensional reports and hydro, UT or PMI reports as ordered. A 3.2 certificate can be arranged when the specification calls for it.