Weld neck flanges, spectacle blinds and water-works flanges for the Doyang hydro station and Wokha water schemes, made at our ISO 9001:2015 works in Mumbai and sent by road with EN 10204 3.1 certificates. The lead time is stated on your written quote.
High-volume water diversion, penstocks & cooling loops: Large-Diameter Flanges, Concentric Reducers.
Lead time for Wokha is stated on your written quote.
Heat numbers marked on every piece; third-party inspection accepted.
Carbon, alloy, stainless and duplex grades supplied with an EN 10204 3.1 MTC.

The biggest piece of plant in Wokha district is the Doyang hydro station, and its overhaul and repair work is where most flange enquiries start. Remax Forge quotes hydro and thermal station weld neck flanges, isolation spectacle blinds for power plants and slip-on flanges for water mains for that work and for district water schemes, made in Mumbai with an EN 10204 3.1 MTC. Nearby pages: Mokokchung and Dimapur.
At Remax Forge & Fittings, every order is built to the governing standard. For high-pressure steam, oil and gas, and chemical utilities, all piping hardware is manufactured under a certified ISO 9001:2015 quality management system in our Mumbai facility. Before dispatching any order to Wokha, every item undergoes rigorous destructive and non-destructive quality testing. This includes Positive Material Identification (PMI), hydrostatic pressure testing, ultrasonic flaw detection, and dimensional audits to ASME B16.5, B16.47, and B16.11 standards. Every dispatch is accompanied by an EN 10204 3.1 Mill Test Certificate (MTC), dimensional reports, and compliance docs.
The Doyang Hydro Electric Project uses the Doyang River, a Brahmaputra tributary, about 30 km from Wokha town. It has three 25 MW units, 75 MW in all, was commissioned in 2000 and is run by NEEPCO. Reporting in 2026 described landowners still pressing grievances from the 1984 land acquisition, and noted the state's 12 percent share of free power from the station.
A station of this age is maintained unit by unit. Cooling water, drainage and dewatering pumps, governor oil and spiral-case drains all have flanged joints, and an overhaul often needs spectacle blinds to isolate one unit while the others run. Carbon steel A105 in Class 150 or 300 covers most of this; stainless is used on oil and instrument lines.
Town water supply is the other buyer. Nagaland's PHED commissioned a scheme in Wokha in 2018 to serve about 600 households, and works like this use slip-on and blind flanges in PN10/PN16 at pumps, valves and future tie-ins. Contractors on such schemes usually need the flange drilling to match valves already bought, so state the valve standard on the RFQ.
| Service | Flanges & fittings usually specified |
|---|---|
| Cooling water and dewatering pumps | A105 weld neck, raised face, Class 150 or 300 |
| Unit isolation during overhauls | Spectacle blinds and spacers in the line class |
| Governor oil and instrument lines | SS 316 socket weld or threaded, Class 300 |
| Town water mains and valves | Slip-on and blind, PN10/PN16, A105 |
What we quote most often for Doyang Hydro Electric Project, Wokha town water supply. Sizes, classes and grades below are those listed on our flange product pages; anything else is quoted against your specification.
| Types we quote | hydro and thermal station weld neck flanges, isolation spectacle blinds for power plants, slip-on flanges for water mains, plus blinds and spectacle blinds in the same class |
|---|---|
| Dimension standards | ASME B16.5 (NPS ½"–24"), ASME B16.47 Series A/B (NPS 26"–60"), EN 1092-1 (PN6–PN400) |
| Rating range | Class 150, 300, 400, 600, 900, 1500, 2500; PN6 to PN400 |
| Grades for Wokha service | A105 for station water and drainage; SS 316 for oil and instrument lines; A105 for town water mains |
| Face options | RF, FF, RTJ, tongue & groove, male & female |
| Certificates | EN 10204 3.1 MTC with heat number on each piece; 3.2 on request |
| Dispatch | By road from Mumbai to Wokha; lead time on the written quote |

Weld neck, slip-on, blind and threaded flanges to ASME B16.5 / B16.47 in A105, A350 LF2 (low-temp), Class 150–2500, for hydro power piping in Wokha.

ASME B16.9 elbows, tees, concentric and eccentric reducers and caps, seamless or welded and matched to your pipe schedule, for food & agro lines in Wokha.

ASME B16.11 socket-weld and threaded fittings in 3000# and 6000# (9000# on request) for small-bore drain, vent, instrument and hydraulic lines at food & agro units in Wokha.
Flanges and forged fittings are made under an ISO 9001:2015 quality system at our Mumbai works. Alloy and stainless lots get 100% PMI, and hydrostatic, ultrasonic, radiography and magnetic particle testing are available on request. Every dispatch ships with an EN 10204 3.1 MTC.
CNC machining and in-house forging cover standard and drawing-based parts: forged fittings in 2000#, 3000#, 6000# and 9000#, and flange faces in RF, FF, RTJ, tongue & groove and male-female.
We export to 45+ countries, including the UAE, USA and Saudi Arabia. Common sizes and grades are held in stock, so ex-stock orders are dispatched within 24–48 hours.
Our team helps you pick the pressure class, material grade and face type for your service conditions. You are welcome to audit the Mumbai works in person or by video before ordering.
Precision-engineered components for mission-critical environments.

High-volume water diversion, penstocks & cooling loops
Large-Diameter Flanges, Concentric Reducers

Sanitary grade pipelines and food manufacturing lines
SS 304/316 Flanges, Buttweld Elbows
Route: Road freight from Mumbai to Wokha. The lead time and delivery schedule depend on the items and testing ordered and are stated on the written quote. Packing: crates or pallets with rust-preventive coating. Docs: invoice, packing list, EN 10204 3.1 MTC, test reports as ordered.
Wooden crates or pallets, with rust-preventive coating and wrapping to protect machined faces in transit and site storage.
Invoice, packing list, EN 10204 3.1 MTC, PMI reports, hydro test reports, and IBR documentation (if applicable) are dispatched with every order.


























































































Yes, through the overhaul contractor. Give the line size, class, facing and the gap between the flanges, and we quote spectacle blinds or a spade and spacer pair. We are not a NEEPCO-registered vendor.
A weld neck flange in A105 to ASME B16.5 Class 150 or 300 is the usual choice, because the tapered hub copes better with vibration and pressure surges than a slip-on.
Yes. Tell us the valve end standard, for example PN16 to EN 1092-1 or Class 150 to ASME B16.5, and the flanges are drilled to match.
Yes. SS 316 socket weld or threaded flanges in Class 300 are common for small oil and instrument lines. Give the pipe schedule so the socket bore is right.
Orders go by road from our Mumbai works. The lead time depends on the types, sizes and tests ordered, so it is stated item by item on the written quote for Wokha rather than as a fixed number of days.
No. Manufacturing and testing are at our ISO 9001:2015 works in Mumbai, and Wokha orders are sent from there by road. We have no office or warehouse in Wokha.
EN 10204 3.1 mill test certificates, with dimensional reports and hydro, UT or PMI reports as ordered. A 3.2 certificate can be arranged when the specification calls for it.