Weld neck, slip-on and blind flanges for the pumping mains, reservoirs and treatment works that supply Kohima, made at our ISO 9001:2015 works in Mumbai and sent by road with EN 10204 3.1 certificates. The lead time is stated on your written quote.
Municipal water distribution, water treatment & supply mains: Mild Steel Flanges, Concentric Reducers, Weld Bends.
Lead time for Kohima is stated on your written quote.
Heat numbers marked on every piece; third-party inspection accepted.
Carbon, alloy, stainless and duplex grades supplied with an EN 10204 3.1 MTC.

Water is pumped uphill to Kohima, and the rising mains, reservoirs and treatment works on those schemes take most of the flanges bought for the capital. Remax Forge supplies blind flanges for washouts and tie-ins, lap joint flanges with stub ends and weld neck flanges for pump discharge for this work from Mumbai, with an EN 10204 3.1 MTC on every piece. See also Dimapur and Mokokchung.
At Remax Forge & Fittings, every order is built to the governing standard. For high-pressure steam, oil and gas, and chemical utilities, all piping hardware is manufactured under a certified ISO 9001:2015 quality management system in our Mumbai facility. Before dispatching any order to Kohima, every item undergoes rigorous destructive and non-destructive quality testing. This includes Positive Material Identification (PMI), hydrostatic pressure testing, ultrasonic flaw detection, and dimensional audits to ASME B16.5, B16.47, and B16.11 standards. Every dispatch is accompanied by an EN 10204 3.1 Mill Test Certificate (MTC), dimensional reports, and compliance docs.
Nagaland PHED's annual report describes an augmentation scheme for Kohima town, funded 90:10 through the Union urban development ministry, that pumps water from the Zarü stream to a reservoir at Kigwema village in two stages. A larger project, Augmentation of Water Supply to Kohima Town from the Teupuiki/Dzupfu River, has been tendered by PHED with New Development Bank loan funding and a 60-month completion period.
Pumping a town on a ridge means high static head on the rising main. Flanges near the pumps may need PN25 or PN40 (or ASME Class 300) even where the mains further up run at PN10 or PN16, so the rating should be worked out stage by stage, not set once for the whole scheme. Weld neck flanges suit the pump discharge; lap joint flanges with stub ends make stainless sections easier to line up on site.
Reservoirs and treatment works add blind flanges for future connections and washouts, and puddle or wall flanges where pipes pass through concrete. If the contractor supplies a drawing with the nozzle schedule, we quote from it directly and flag any item that is outside our product range.
| Service | Flanges & fittings usually specified |
|---|---|
| Pump discharge on the rising main | Weld neck RF, PN25/PN40 or Class 300, A105 |
| Upper mains and valve chambers | Slip-on or weld neck, PN10/PN16, A105 |
| Stainless sections and treatment piping | Lap joint with SS 304/316 stub ends, PN10/PN16 |
| Washouts and future tie-ins | Blind flanges rated the same as the main |
What we quote most often for Zarü stream pumping scheme, Teupuiki/Dzupfu River project. Sizes, classes and grades below are those listed on our flange product pages; anything else is quoted against your specification.
| Types we quote | blind flanges for washouts and tie-ins, lap joint flanges with stub ends, weld neck flanges for pump discharge, plus blinds and spectacle blinds in the same class |
|---|---|
| Dimension standards | ASME B16.5 (NPS ½"–24"), ASME B16.47 Series A/B (NPS 26"–60"), EN 1092-1 (PN6–PN400) |
| Rating range | Class 150, 300, 400, 600, 900, 1500, 2500; PN6 to PN400 |
| Grades for Kohima service | A105 for pumping mains; SS 304/316 stub ends for treatment piping |
| Face options | RF, FF, RTJ, tongue & groove, male & female |
| Certificates | EN 10204 3.1 MTC with heat number on each piece; 3.2 on request |
| Dispatch | By road from Mumbai to Kohima; lead time on the written quote |

Weld neck, slip-on, blind and threaded flanges to ASME B16.5 / B16.47 in A105, SS 304, galvanized options, Class 150–2500, for water & utility piping in Kohima.

ASME B16.9 elbows, tees, concentric and eccentric reducers and caps, seamless or welded and matched to your pipe schedule, for food & agro lines in Kohima.

ASME B16.11 socket-weld and threaded fittings in 3000# and 6000# (9000# on request) for small-bore drain, vent, instrument and hydraulic lines at food & agro units in Kohima.
Flanges and forged fittings are made under an ISO 9001:2015 quality system at our Mumbai works. Alloy and stainless lots get 100% PMI, and hydrostatic, ultrasonic, radiography and magnetic particle testing are available on request. Every dispatch ships with an EN 10204 3.1 MTC.
CNC machining and in-house forging cover standard and drawing-based parts: forged fittings in 2000#, 3000#, 6000# and 9000#, and flange faces in RF, FF, RTJ, tongue & groove and male-female.
We export to 45+ countries, including the UAE, USA and Saudi Arabia. Common sizes and grades are held in stock, so ex-stock orders are dispatched within 24–48 hours.
Our team helps you pick the pressure class, material grade and face type for your service conditions. You are welcome to audit the Mumbai works in person or by video before ordering.
Precision-engineered components for mission-critical environments.

Municipal water distribution, water treatment & supply mains
Mild Steel Flanges, Concentric Reducers, Weld Bends

Sanitary grade pipelines and food manufacturing lines
SS 304/316 Flanges, Buttweld Elbows
Route: Road freight from Mumbai to Kohima. The lead time and delivery schedule depend on the items and testing ordered and are stated on the written quote. Packing: crates or pallets with rust-preventive coating. Docs: invoice, packing list, EN 10204 3.1 MTC, test reports as ordered.
Wooden crates or pallets, with rust-preventive coating and wrapping to protect machined faces in transit and site storage.
Invoice, packing list, EN 10204 3.1 MTC, PMI reports, hydro test reports, and IBR documentation (if applicable) are dispatched with every order.


























































































It depends on the static head plus surge at that point. Where the pressure exceeds 16 bar, PN25 or PN40 to EN 1092-1, or ASME Class 300, is needed. Send the head or pressure for each stage and we quote the matching rating.
The loose backing flange turns freely, so bolt holes line up easily during installation, and only the stub end touches the water. That lets a carbon steel backing flange be used with a stainless stub end.
Yes. Send the drawing or schedule; the quote lists each flange we can supply and marks any item outside our range.
Send the drawing and we will confirm on the quote whether we can make it; standard flanges are made to ASME B16.5 and EN 1092-1, and special shapes are quoted case by case.
Orders go by road from our Mumbai works. The lead time depends on the types, sizes and tests ordered, so it is stated item by item on the written quote for Kohima rather than as a fixed number of days.
No. Manufacturing and testing are at our ISO 9001:2015 works in Mumbai, and Kohima orders are sent from there by road. We have no office or warehouse in Kohima.
EN 10204 3.1 mill test certificates, with dimensional reports and hydro, UT or PMI reports as ordered. A 3.2 certificate can be arranged when the specification calls for it.